Q6S47Y pneumatic high-pressure hard seal cut-off ball valve will automatically reset to the closed or open state when the on-site air source is lost.The middle flange is connected by bolts, and both the upper and lower valve stems are equipped with sliding bearings to reduce friction, making operation effortless and stable.Under normal circumstances: when the pressure is low, the valve seat seal relies on the pre tightening force of the spring to make the valve seat tightly adhere to the sphere for sealing. When the pressure is high, a piston effect is formed on the valve seat, and under the pressure of the upstream medium, the valve seat presses against the sphere for sealing.Especially suitable for situations where the medium is viscous, contains particles, and has fiber properties. Widely used in industrial automatic control systems such as petroleum, chemical, teaching equipment, light industry, high-pressure equipment, pharmaceuticals, paper making, etc., for remote centralized control or on-site control.
Product features:
1）The three-way connection forged steel fixed ball valve is divided into three parts by dividing the valve body into three sections perpendicular to the axis of the valve channel at the two valve seats,entire valve is symmetrical about the center axis of the valve stem.
2）It is mainly used in pipelines to cut, distribute, and change the direction of medium flow.
3）Its large pivot structure ensures accurate center position of the sphere under high pressure, ensuring good operational performance of the valve.
4）The standard valve seat adopts a spring structure, which pushes the valve seat towards the sphere, ensuring good bidirectional sealing performance at the inlet and outlet.
5）By using the built-in discharge valve, the middle chamber of the valve body can discharge outward.
6）The pivot adopts an anti blow out protection structure, effectively preventing leakage.
7）Low friction coefficient bearings minimize torque and facilitate valve opening and closing.
8）The effective contact between the valve stem and valve body ensures superior performance of the anti-static grounding device.
9）It has the advantages of excellent performance, high reliability, wide application, and reasonable price.
Execution standards:
Design and manufacturing: GB/T12237-2007
Structural length: GB12221-2005
Supply requirements: GB/T12252-2005
Pressure test: GB/T13927-2008
Pressure testing and inspection: GB/T13927-1992
Description of ball valve model preparation:
|
Q6S47Y Pneumatic High Pressure Hard Seal Cut off Ball Valve Model Compilation |
|
Valve type |
Drive mode |
Connection form |
Structural form |
Sealing material |
Nominal Pressure |
Valve body material |
|
Q:Ball valve |
6S：Pneumatic with manual |
4:Flange |
7:Fixed through type |
Y:Ni60 |
-10:PN6.4MPa
-16:PN10.0MPa |
C:Carbon steel
P: Chromium nickel stainless steel
R: Chromium nickel molybdenum stainless steel |
Main technical parameters:
|
Q6S47Y pneumatic high pressure hard seal cut off ball valve performance parameters |
|
Valve type |
Drive type |
Connection form |
Structural type |
Sealing surface |
Nominal Pressure（MPa） |
Valve body material |
|
Ball valve |
6-Pneumatic
6s - Pneumatic with manual |
4-Flange type |
Fixed ball through |
F-Fluoroplastics
H-alloy steel
PPL |
6.4
10.0
16.0
24.0 |
According to the valve body in the table
Material code |
|
Nominal Diameter DN（mm） |
50-500 |
|
Material code |
C |
P |
R |
|
Main Parts |
Valve body |
WCB |
ZG1Cr18Ni9Ti |
ZG1Cr18Ni12Mo2Ti |
|
Ball disk |
2Cr13 |
1Cr18Ni9Ti |
1Cr18Ni12MoTi |
|
Valve stem |
2Cr13 |
1Cr18Ni9Ti |
1Cr18Ni12MoTi |
|
Sealing ring |
Enhanced PTFE para polybenzenes |
|
Filler |
PTFE flexible graphite |
|
Applicable working conditions |
Applicable medium |
Water,steam,oil |
Nitric Acid |
Acetic acid |
|
Applicable temperature |
-28℃～300℃ |
|
Control type |
Double acting/single acting |
|
Mode of action |
Cut off/adjust |
|
Input signal |
Electrical signal: 0 ~ 10mA, -4 ~ 10mA gas signal 20 ~ 100kPa |
|
Return voltage |
AC220V/DC24V |
|
Working medium |
Clean compressed gas |
|
Actuator |
Model |
GT series, HY series, AW series, ZSH series, etc |
|
Gas source pressure |
0.4～0.7MPa |
Product dimensions table:
|
Q6S47Y Pneumatic High Pressure Hard Seal Cut off Ball Valve External Structure Connection Dimensions |
|
Nominal Diameter DN（mm） |
Size（mm） |
Actuator Model |
|
1.6MPa |
2.5MPa |
4.0MPa |
|
L |
D |
D1 |
B |
Z-φD |
L |
D |
D1 |
B |
Z-φD |
L |
D |
D1 |
B |
Z-φD |
|
50 |
203 |
160 |
125 |
16 |
4-18 |
216 |
160 |
125 |
20 |
4-18 |
216 |
160 |
125 |
20 |
4-18 |
Optional GTD/GTE, AW/AWS, HY, ZSH series actuators (the above options are only for selection and specific selection depends on actual requirements) |
|
65 |
222 |
180 |
146 |
18 |
4-18 |
241 |
180 |
145 |
22 |
8-18 |
241 |
180 |
145 |
22 |
8-18 |
|
80 |
241 |
195 |
160 |
20 |
8-18 |
283 |
195 |
160 |
22 |
8-18 |
283 |
195 |
160 |
22 |
8-18 |
|
100 |
305 |
215 |
180 |
20 |
8-18 |
305 |
230 |
190 |
24 |
8-23 |
305 |
230 |
190 |
24 |
8-23 |
|
125 |
356 |
245 |
210 |
22 |
8-18 |
381 |
270 |
220 |
28 |
8-25 |
381 |
270 |
220 |
28 |
8-25 |
|
150 |
394 |
280 |
240 |
24 |
8-23 |
403 |
300 |
250 |
30 |
8-25 |
403 |
300 |
250 |
30 |
8-25 |
|
200 |
457 |
335 |
295 |
26 |
12-23 |
502 |
360 |
310 |
34 |
12-25 |
502 |
375 |
320 |
38 |
12-30 |
|
250 |
533 |
405 |
355 |
30 |
12-25 |
586 |
425 |
370 |
36 |
12-30 |
|
|
|
|
|
|
300 |
610 |
460 |
410 |
30 |
12-25 |
648 |
485 |
430 |
40 |
16-30 |
|
|
|
|
|
|
350 |
686 |
520 |
470 |
34 |
16-25 |
762 |
550 |
490 |
44 |
16-34 |
|
|
|
|
|
|
400 |
762 |
580 |
525 |
36 |
16-30 |
838 |
610 |
550 |
48 |
16-34 |
|
|
|
|
|
|
450 |
864 |
640 |
585 |
40 |
20-30 |
914 |
660 |
600 |
50 |
20-34 |
|
|
|
|
|
|
500 |
914 |
705 |
650 |
44 |
20-34 |
991 |
730 |
660 |
52 |
20-41 |
|
|
|
|
| |
